Bath towels still clammy once the program wraps up, a tumbler that rotates yet never warms, or squeaking that carries two floors away? Our technician comes by your Barrie house, pinpoints the tired component and gets every load finishing dry on the first go.
Electric, gas and stacked dryers around Barrie usually fail in one of these ways. Our opening checks appear beneath each heading.
An open circuit in the heater coil, a one-shot fuse that tripped or a glowing gas igniter that never gets a flame going.
We check: heating element, thermal fuse, gas igniter
You hear the motor working yet the drum won't budge, typically from a broken belt or an idler pulley frozen in place.
We check: drive belt, idler pulley, drive motor
Flat-spotted rollers, worn glides or a dry rear bearing make every cycle noisy.
We check: drum rollers, front glides, rear bearing
Fabric softener film coating the sensor strips, or a thermostat switching off too soon, ends the program before the load is dry.
We check: moisture sensor, cycling thermostat, control board
The door switch doesn't register, the start button wore out or the board isn't receiving power.
We check: door switch, start switch, main board
A high-limit switch fused closed or a misreading sensor lets heat keep climbing. Switch it off and leave it until we've tested it.
We check: high-limit thermostat, thermistor, heater relay
Dryers we work on
Korean, American and European names alike: our team works on the makes Barrie homeowners actually own, from basic builder units to premium built-ins, with service manuals and the right tools for each.
Book NowBrand not listed? Ask anyway, there's a good chance it's one we handle too.
Haier and KitchenAid dryers display a code whenever a program can't carry on. Find yours in the list below.
Door not closed
Push the door shut until it latches, then start the program again.
Try this firstEmpty or already dry
Either nothing is inside or the laundry has already dried. Switch off and choose a program again.
Try this firstTemperature sensor fault
The heat-sensing circuit reads as open or shorted and needs testing.
Call a technicianCondensate pump failure
On condenser models, the pump that removes collected water has stopped working.
Call a technicianPower interrupted
Power dropped during the cycle. Hold Start to continue, or press Power to clear the display.
Try this firstLow supply voltage
Check both breakers and the cord connection. If the outlet still lacks full voltage, call an electrician.
Try this firstHeater or relay problem
The heater circuit or its relays may have failed. Should it reappear once the breaker is reset, book service.
Call a technicianControl communication error
The main board and touchpad aren't communicating, pointing to a board or wiring fault.
Call a technicianCode missing here, or returning right after you restart? Give the office a ring for a home visit.
(249) 202-8722Barrie households folding warm, dry laundry again.
Every load needed two runs and still came out cool. He fitted a fresh heater during that first visit and now jeans dry in one go.
The squealing was so bad the kids complained. Rollers and belt replaced, and now it's practically silent. Very tidy work.
Pressing Start did nothing at all. A worn-out door switch was to blame, and he replaced it while explaining each step. Quick and honest.
Some stubborn dryers only need a moment of attention. Look over these points first.
Breaker reset
On electric units, cycle the two-pole breaker completely off and then on.
Lint screen cleared
Clear it each time you dry, and scrub it with warm water if sheets have left a coating.
Door latching
Check that no sleeve is pinched at the edge and the latch clicks shut.
Sensible load size
Split very large loads so clothes can tumble freely.
Best left to a pro
Still need two cycles?
Anything past these checks should go to certified and insured technicians.
Drop your details into the form and our Barrie office will phone you back to arrange a convenient arrival. No long hold music, no guessing when someone will show.
Rather talk to a person right now?
(249) 202-8722Request your visit
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
